Why Is My RELX Firing by Itself?
You put your RELX down on the desk, and it starts glowing and crackling with nobody touching it. That’s unsettling, and you’re right to take it seriously. Here’s why your RELX is automatically firing: Every RELX device in this guide fires when you draw, not when you press a button. A small sensor detects the airflow from your inhale. When moisture, condensation, or leaked e-liquid reaches that sensing area, the sensor can read it as a puff and fire on its own. This guide covers these models:
- RELX Artisan
- RELX Essential
- RELX Infinity
- RELX Infinity Plus
- RELX Infinity 2
One quick check first. If the light stays on for just a second after you stop inhaling, that’s normal. Genuine auto-firing means the device heats without any draw at all or keeps firing long after you stop.
First: Stop the Auto-Firing Safely
If your RELX keeps firing, stop using it right away and remove the pod, as long as it comes out normally. Removing the pod is always your first step before any cleaning or testing. Here’s why:
- Constant firing builds heat inside a small device.
- It drains the battery fast and can burn out the coil in the pod.
- Every extra test on a faulty device adds risk for no reason.
Don’t keep puffing to see if it stops. Also, don’t shake it, tap it hard, poke it, open it, or tamper with the electronics.
The Most Common Reason RELX Auto-Fires: Condensation and E-Liquid
How Condensation Can Trigger the Draw Sensor
Every puff sends warm vapor through the pod. Some of it cools and turns back into tiny droplets inside the pod and around its base. Over time, those droplets can settle near the airflow path the sensor watches. When that happens, the sensor can mistake the moisture for a draw. A bit of condensation is normal for any pod system like RELX Pod Pro, from the premium RELX Artisan to the most basic device. It doesn’t mean your device is broken. It means the area needs drying.
How a Leaking Pod Can Cause Auto-Firing
Condensation leaves light droplets. A leak means actual e-liquid escaping the pod. Watch for:
- Visible liquid on the pod or in the device cavity
- A wet, sticky feel around the pod base
- Moisture is coming back soon after you clean it.
- Liquid getting into the device opening
A cracked, damaged, or constantly leaking pod needs replacing. Don’t keep cleaning and reusing it. Old pods can also be a factor, so check whether RELX pods expire.
Other Possible Trigger: Debris and Pocket Lint
Carry your RELX loose in a pocket, and lint, dust, or sand can work its way into the pod cavity. On their own, a few specks rarely matter. Mixed with moisture, though, they can form a damp residue that interferes with the sensor and contact area. Keeping that area clean and dry solves most of it, whether you carry a RELX Essential or any other model.
RELX Auto Firing Fix: Step-by-Step Cleaning Protocol
This is the core RELX auto firing fix. Follow it in order.
- Step 1: Remove the pod. Pull it out normally and place it on a clean, dry surface. Don’t use the device while it’s auto-firing.
- Step 2: Inspect the pod cavity. Look for droplets, e-liquid, dust, or lint around the pod connection and any airflow openings you can see.
- Step 3: Dry the accessible moisture. Use a dry cotton swab or clean tissue to gently soak up visible moisture, especially on the metal contacts. Never pour water, alcohol, or cleaner into the device, and don’t push tissue deep inside.
- Step 4: Clean the contact area gently. Wipe residue off the metal contact points you can reach. Don’t scrape, bend, or force them.
- Step 5: Let it dry. Leave the device pod-free for a few hours so any remaining moisture can evaporate. Never use a hair dryer or any heat source to speed it up.
For regular upkeep beyond this fix, see these RELX maintenance tricks.
Check the Pod: Condensation Glitch or Leaking Pod?
| What you find | Likely situation | What to do |
|---|---|---|
| A little condensation | Temporary moisture | Dry it and keep an eye on it |
| Wet pod contacts | Liquid reaching the connection | Clean and dry the area |
| Cracked pod | Physical damage | Replace the pod |
| Liquid keeps leaking | Faulty pod | Replace the pod |
| Device stays wet after repeated cleaning | Liquid inside the device | Stop using it, get support |
| Auto-firing with a new pod | Likely a device fault | Stop using it, get support |
The last two rows matter most. Once the problem points to the device itself, stop troubleshooting.
Test With a Known-Good Pod
Only try this once the device has stopped auto-firing and you’ve dried the cavity. Insert a fresh, undamaged, genuine RELX pod like RELX Pod Pro 2 that fits your model, such as a new pod in your RELX Infinity, and watch it for a minute without drawing.
- Problem gone? The old pod was most likely leaking or damaged.
- Problem back? The device probably has a sensor or internal fault.
If it starts firing again right away, remove the pod and stop. Don’t keep swapping pods to test it.
Why a RELX Doesn’t Usually Have a “Stuck Fire Button”
Many generic vape guides blame a stuck fire button. That advice doesn’t fit RELX. Every model here fires when the sensor detects a draw, as the RELX user manual explains. There’s no fire button to stick. So focus your RELX device troubleshooting on:
- Condensation
- E-liquid leaks
- Blocked airflow
- Debris
- A dirty sensor or contact area
- An internal fault
The RELX Infinity 2 does have a button on the side, but it only cycles power modes: Eco, Smooth, and Boost. It doesn’t fire the coil, so it isn’t the cause of auto-firing. Curious how air moves through the device? Read RELX airflow explained.
RELX Device Troubleshooting by Model
| Model | What to check |
|---|---|
| RELX Artisan | Pod condition, moisture in the pod cavity, dry contact points |
| RELX Essential | Pod leaks, a dry connection area, debris near the airflow openings |
| RELX Infinity | Pod fit and condition, moisture at the connection, replace damaged pods |
| RELX Infinity Plus | Same moisture, pod, and airflow checks; get support if it continues |
| RELX Infinity 2 | Pod condition and sensor area; the mode button doesn’t cause firing |
The lights can help you read what’s happening too. Use this RELX blinking light guide to decode them.
What Not to Do When Your RELX Auto-Fires
Don’t:
- Keep inhaling while it fires by itself.
- Trigger it again and again to “test” it.
- Pour liquid or cleaner into the device.
- Push sharp objects into the pod cavity.
- Open the device.
- Try to repair the sensor or battery yourself.
- Use a cracked or leaking pod.
- Keep using it if it gets unusually hot or acts strangely.
When a RELX Auto-Firing Problem Means You Should Stop Using the Device
Cleaning fixes moisture. It can’t fix a faulty sensor or battery on any model, the RELX Infinity Plus. Stop using the device and contact your retailer or RELX support if:
- It keeps firing without a draw.
- Auto-firing returns right after cleaning.
- It auto-fires with a fresh pod.
- It gets unusually hot.
- Liquid has clearly gotten inside it.
- It has cracks, dents, or other damage.
- It acts strangely while charging.
- Basic external cleaning doesn’t solve it.
How to Prevent RELX Auto-Firing Problems
If you want to know how to stop a vape from auto firing before it starts, build these habits:
- Replace leaking or cracked pods straight away.
- Wipe the pod cavity dry every time you change pods.
- Don’t let e-liquid build up on the contacts.
- Keep the device away from water, steam, and humid spots like bathrooms.
- Carry it in a clean pocket or case, not loose with lint and keys.
- Handle it gently so the pod and body don’t crack.
- Follow RELX’s storage, charging, and usage guidance.
Many smokers who switch never run into these problems once the habits stick, as this cigarettes to RELX switch story shows.
FAQ: RELX Automatically Firing
Why is my RELX automatically firing?
Most often, condensation or leaked e-liquid reaches the draw sensor area and makes it detect a fake puff. Debris mixed with moisture can do the same. If cleaning doesn’t help, the device itself likely has a fault.
How do I stop my RELX from auto-firing?
Stop using it and remove the pod. Then inspect the cavity, dry what you can reach, and check or replace the pod. If it keeps firing, contact support.
Can condensation make a RELX fire by itself?
Yes. Moisture near the airflow and sensor area can trick the sensor into reading a draw.
Can a leaking RELX pod cause auto-firing?
Yes. A leak puts much more liquid near the sensor than normal condensation does, and it keeps coming back until you replace the pod.
Should I replace my RELX pod if it is cracked?
Yes. A cracked pod keeps leaking, so cleaning only delays the problem. Swap it for a fresh one.
Can pocket lint cause RELX auto-firing?
Yes, especially combined with moisture. Lint can block airflow and leave a damp residue on the sensor and contact area.
Should I clean the inside of my RELX?
No. Clean only the pod cavity and the contacts you can reach. Never open the device or try internal repairs.
What if my RELX keeps auto-firing after I clean it?
Stop using it and contact RELX or your retailer. Repeated testing won’t fix an internal fault, and it adds risk.
Final Takeaway
When your RELX fires on its own, follow this order and fix auto-firing vape problems safely:
- Auto-firing
- Remove pod
- Check for leaks or condensation
- Dry what you can reach
- Replace a damaged pod
- Test only when it’s safe
- Stop and get support if it continues.
The main point is simple: a RELX that fires without a draw isn’t something to keep testing or ignore.
Where to Buy Genuine RELX Devices and Pods in the UAE
Genuine pods and devices cut down on leaks and fit problems. RELX Dubai sells authentic RELX devices with warranty and QR-verifiable packaging, plus 1 to 2 hour delivery in Dubai, Sharjah, and Ajman, same-day delivery across the rest of the UAE, and free shipping on orders over AED 300. Sales are for adults only.
Vape products contain nicotine, which is addictive.